Home > Catalog > Roof Products > Metal Roof Rust Inhibitive Primer

Metal Roof Rust Inhibitive Primer

RP-MRRIP-Q

This Product is Available Only To:
DEALERRV OWNER

Dicor Metal Roof Rust Inhibitive Primer is specifically formulated to reduce further corrosion of metal roofs and enhances the adhesion of Dicor Elastomeric Metal RV Coating. Previous present rust must be removed first for this inhibitive primer to work properly. Not recommended for EPDM RUBBER OR TPO ROOFING

Available in:

1 Qt. can


Print

Dicor Metal Rood Rust Inhibitive Primer is specifically formulated to reduce further corrosion of metal roofs and enhances the adhesion of Dicor Metal RV Coating.

  • Helps Control rust
  • Acrylic rust inhibitive resin
  • Enhances adhesion of Dicor Elastomeric Metal RV roof Coating
  • Easy to apply
  • Soapy Water Clean Up
Part NumberDescriptionPriceUnitQuantity

Part Number: RP-MIIRP-Q      1 Quart (32 fl oz)

Remove all loose dirt, oil, rust, chalk, mildew, loose coating or other contaminants, which would prevent maximum adhesion of Dicor Rust Inhibitive Primer. If chalk remains on a previously painted roof, repeated washing may be necessary. Thoroughly rinse with water and allow to dry completely before proceeding. Be sure all surfaces are sound and clean, and all rust has been removed down to bright metal, using mechanical methods such as wire brush, sandpaper or steel wool. Prime clean rust removed areas with Dicor Metal Rust Inhibitive Primer. Seal all fasteners and around all roof protrusions and vent mountings (vents, lander stanchions, etc.) with Dicor Lap Sealant. Seal all joints and roof seams with Dicor Coating Ready Cover Tape, prior to applying the top coat. It is recommended to cover and protect the exterior sidewalls as well as front and rear caps of the RV with plastic sheeting to avoid the coating sticking to surfaces other than the roof. If coating comes in contact with any surface other than the roof, wash it off immediately.

Rust Inhibitive Primer Application: Apply, un-thinned, at the rate of 200 square feet per gallon, per coat. For maximum performance, two coats are required. Apply each coat at right angles to each other by brush or roller. First primer coat must be dry before second coat of primer is applied. Under normal conditions of 70°F and 50% relative humidity, the second primer coat may be applied within 1 to 2 hours at the same rate as the first coat. In order to prevent any chance of “wash off” of freshly applied primer, do not apply at temperatures below 50°F, or when rainfall, cold, darkness or high humidity are expected within 4 hours after application. During these 4 hours, at least 2 hours should be of direct sunlight. Top coat may be applied after primer coat is dry.

Clean Up: Clean brushes, tools and other equipment with soapy water immediatelyafter use. Dried film is difficult to remove from any surface. Ifcoating is subjected to rain, before it has properly dried, and washoff occurs, it is necessary to immediately wash stained surfaces withsoapy water to prevent staining.

Warning! If you scrape, sand or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID EXPOSURE.

Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead

Caution:

  • Do not take internally
  • Close containter after each use
  • Use with adequate ventilation
  • Use protective clothing to avoid contact with fiberglass, skin or eyes
  • Keep away from children
  • Do not allow product to freeze

FOR TRANSPORTATION EMERGENCIES CALL CHEMTREC: 800-424-9300